Showing posts with label reloading tools. Show all posts
Showing posts with label reloading tools. Show all posts

Wednesday, August 10, 2016

Magnetospeed V3 Chonograph $323 at Primary Arms.

Magnetospeed V3 @ Primary Arms

Regular price $380.  $323 with promotion code "RANGE."

I have been using one for a few months with the Picatinny adapter on pistols. More expensive than sky screen chonographs, but I wasn't using mine because they are a pain in the hind-end to set up.  It takes maybe 30 seconds to clip-on, or strap-on the Magnetospeed "bayonet" and plug it into the box, and that's pretty much all it takes to set one up.

There is a cheaper Sporter model, but it isn't compatible with the Picatinny mount.

I'll probably write up a review eventually.  Real short story - I use one, and I like it.

Saturday, October 13, 2012

Review: Lee Pacesetter .223Rem Dies


All my reloading dies are LEE.  Started loading .45ACP, and then 9mm for a race gun.  Then ammo started getting more and more expensive, and I started using the 9mm dies a lot more.  Loaded over 10,000 rounds with these LEE dies.  When I really started shooting carbines, and working up precision loads, I didn't see any point in trying other brands and Lee was pretty commonly recommended for semi-auto rifles.

Initially, I tried using the decapping and resizing die with my Lee hand press while watching TV.  Although this would work fine for two of my rifles, I have one rifle with short(er) headspace.  Using the Lee shell-holder and sizing die that come with the kit, I can not get the brass resized down to factory spec, and the bolt of the one rifle would not fully lock.  Using the sizing die on my progressive press with the shell-plate for that press, I can resize the brass to work with all my rifles.  If I had a belt sander, or better yet a lathe, I could probably shave down the Lee shell-holder to make it work.

On the rifle dies, the lock-ring with the inset o-rings work nicely.  Maybe it's my technique with the case lube, and lot-to-lot variations in cartridge cases, but I need to make fine adjustments to the resizing die to get consistent headspace dimensions on the casings, and the Lee lock-rings allow for easy adjustments, but they do stay put when set.  It may well be that I'm just too picky about the headspace dimension of resized cases.

The Factory Crimp Die does work.  When the round is raised up into the die, the shell-plate (or shell-holder)  presses on the bottom of the die and the collet closes on the neck of the cartridge case and bullet.  You can adjust the amount of crimp by turning the die in the press.  You can also crimp with the bullet seating die, but I have not tried this.  I don't crimp match bullets, as I have found that is not necessary.  When I'm making bulk ammo for a semi-auto rifle, I'll crimp with the FCD, but when I'm loading ammo for bullseye shooting, I skip the crimp.  I have gotten less than 1" 10-shot groups at 100 yards, and groups around 1 1/8" are fairly common, and I don't really have a .223Rem target rifle.  These groups were shot though a LMT 16" M4 barrel with chrome lining.

FCD collet closed on a round from a recent batch

A micrometer adjustable bullet seating die would be handy, but I nearly passed out when I saw the price for one.  The Lee bullet seating die is easy to adjust with just your fingers, and the micrometer die costs more than double the price of the whole Lee die set.  The LEE seating die gives reasonably consistent overall length when using good bullets.  If you are using cheap bullets your overall length may well be a little inconsistent, but that may be the least of your problems.

The collet-held decapping rod has saved me a couple times.  Even with .223 cases, you can still get pebbles into the neck, and sometimes a Berdan-primed case will make it past my visual inspection.  I have broken a decapping pin, but it was my fault for not using enough case lube to start with, and then I manhandled the pin trying to remove it from the case.  Because the case mouth expander and decapper are all one piece with the Lee dies, you may have to cut the case in half around the pin to remove.  You can buy spare decapper/expander pins direct from LEE, and the current price of $3 is pretty reasonable.

The box I got with the dies is a rectangular one that stacks with my other Lee die boxes.

The only thing, practically speaking, that I would like to see, is an option to have the steel parts plated or otherwise treated to prevent rusting, for an added fee.

I have fired over 2500 rounds of reloads.  The only issues I've had, have been my own fault, with the exception of the rounds that didn't fit the one rifle due to the Lee shell-holder.

Sunday, February 21, 2010

Cabela's/Berry's Tumber Review


For a little while, very little while, I cleaned brass with soap and water, dryed in the oven, and polished by hand with steel wool.  That got old really quick, and I ended up with a few splinters of brass or steel wool in my fingers.

Of the tumblers that were getting good reviews, the Cabela's model and the Berry's were two of the cheapest.  With the exception of external appearances, the two are really the same.  Berry's makes the tumbler for Cabela's.


I believe that the instructions that came with the Cabela's tumbler said to fill it 2/3 with media, and then load in the cases.  The cases seem to come out cleanest and nicely polished when the tumbler is completely filled, and the motor doesn't seem to mind the full load.  You don't have to fill it, obviously, but that's how I get the best results.

I run the tumbler 3 hours with a timer.  Once-fired brass, if not too badly tarnished, comes out nice and clean.  I probably don't need to tumble the once-fired brass from the indoor range the full three hours, and should probably cut that back in the future.  The cases I reload with TiteGroup powder sometimes get scorched, and the tumbler doesn't remove that burn mark.  I don't think that much of anything would remove the burn marks.

I store my cases in 1 Gallon Zip-Loc type bags, and the tumbler will hold about a half gallon worth of brass when filled 2/3 with tumbling media. 

Although I'm not sure when I received it, I ordered it on 2/5/2007, and it's still going, knock on wood.  When I first got it, I didn't have a whole lot of brass, and I was doing a lot of small batches, so I've got a good number of hours on the unit.

Capacity (approximate):
900 9mm casings
550 .45ACP
500 .38SPL
450 .223REM or .357Magnum

Tumbling Tips
You can get big bags of KayTee brand crushed walnut shell at some PetSmart stores sold as bird litter.  It is much cheaper than the stuff sold by reloading suppliers.  I add in some paste brass polish that I picked up from the dollar store, but I hear that NuFinish car polish works well also.

When/if you add liquid or paste polish to your tumbling media, run the tumbler for about 30 minutes without any brass.  If you put in the polish and the brass at the same time, all the polish will end up caked into a few pieces of brass.  It's not good, trust me on this.  If you were tumbling bottlenecked rifle cases, you might have to throw out the pieces with polish and tumbling media stuck in them.

Get yourself a dust mask.  The tumbling media will pick up lead from the primers in the cases, and you don't want to breathe that in.  Besides the lead, dumping the media into a sifter will generate a lot of dust that you'll choke on anyway.

Run your tumbler outside or in your garage where any lead that might get out of it won't contaminate your living space.  The motor in the tumbler can get hot, so don't put it on anything that might melt or ignite, like nylon carpeting or newspaper.

Cabela's Website - It's the model 400 tumbler.  Check RetailMeNot for coupons.
Berry's Mfg. Website - Model 400 tumbler.

WARNING: Vibratory tumblers have been known to attract graboids.  Use at your own risk.

Friday, January 2, 2009

Lee Carbide Pistol Die Set Review

I've loaded something like 10000 rounds of 9mm with these dies, and about 500 rounds of .45ACP.

The decapping pin has never broken on me, knock on wood. The sizing die does a really good job of ironing out bulges, going almost down to the rim.

The flaring die holds onto cases, which shakes the press and causes erratic charges when using a powder measure. The amount of shake varies depending on the brand of brass, and whether the brass is plated, but it shakes the press a lot when used with Remington 9mm brass, which I get a lot of.  I've started using a little bit of Hornady One Shot case lube, the aerosol, which makes sizing and flaring a lot smoother.

The seating/crimp die works well, and doesn't seem to mark up any bullet that I've loaded. I stopped using the Factory Crimp Dies after hearing that they resize the bullet. The seating die does a good job of crimping.

The lock rings don't work all that well with Hornady Lock-N-Load bushings. I imagine the same goes with the new Lee quick-change die bushings. When turning the bushings to remove the die, sometimes the die unscrews a bit, and then you have to reset the die because there's nothing to hold the lock ring in place on the die. I've replaced a couple of the lock rings with Hornady rings, and drilled and tapped all the Lee rings for set-screws.

Sunday, March 9, 2008

Lee Auto Prime - Hand Priming Tool Review

I’ve used mine to prime several thousand pieces of brass, including a couple thousand with the Federal primers that Lee strongly recommends not using with the tool. I could prime on the press, obviously, but I don’t like handling metal tubes full of impact-sensitive high-explosive. I’d rather size/deprime and flare, prime with the Lee tool while watching TV, and then load.

I have not had any problems with breakage so far, knock on wood, though I could imagine that the pivot in the handle might break if there was a casting flaw near that area. I also have some doubts about the latch that holds the plastic primer tray lid on.

The cam (for lack of a better term) did develop notches from priming several thousand pieces. I ground it smooth, and it happened again. I bought another one, and case hardened the "cam" with Casenit, and it seems to be holding up with no sign of wear. Not a big deal considering the tool costs less that $20, and I had lost a spring anyway.

Probably my biggest complaint is that it’s not very comfortable to use. Rubber grips on the handle and lever would be greatly appreciated. This is something that nobody else does either for some reason.

That’s pretty much all there is to say, it’s a simple and affordable tool, and it works.